Hbada Ergonomic Office Chair with 3D Adjustable Armrests, Adjustable Lumbar Support High Back for Computer Chair, Big and Tall Mesh Office Chair, Home Office Desk Chairs White

If you are 6ft 3 inches, perhaps this is not the chair for you…but it is comfortable.
It was very easy to assemble. Quality is good, although some plastic seem a bit cheap. In general for normal people under 6 ft, it is a good chair. Unfortunately for me, it is designed for people of shorter stature. The foot rest would be better for most if it were a bit further out (3 inches or so), and for taller folks, it would need to be out a few inches more. The pedestal hydraulic lift is a bit low, but would fit most people, but over 6 footers, well it leaves a bit to be desired. For the price you pay though, it is easy to purchase a longer one and install it. I haven’t done that, and it might be outside of the designs ability to do the full layback without tipping so if you do, test it first. That is another thing fine about the chair, the full layback and the wide wheel base that allows that to work, where other chairs totally fail when you simply lean back. In any case, I do recommend the chair for those of more normal height.

Great for the price
While the leg rests could be better, maybe a little smaller or with some padding, it’s a great chair and very comfortable for the price.

Cheap for a reason
So I bought this chair in an attempt to improve my growing home office and to finally replace my old $40 IKEA swivel chair. Long story short: I will be returning to my $40 old chair and hopefully be able to return this HBada to get my money back at least.I ordered the chair on June 30th and it arrived July 2and in a very large, heavy, and beat up box. The outer cardboard of the main box had several holes/punctures on the bottom which were stained with some dark residue in patches about 2 inches across. It also appeared that the box had sustained some sort of crushing/compacting force during transit as one of the corners where the cardboard was thinner had nearly spit open.Disregarding all of the above I pressed on and opened up the box as cleanly as I could and set to assembling. Assembly was straightforward and not particularly difficult, there was a bit of novelty in using the included hex key due to it’s odd proportions but no issues. However, it was during the assembly that I started to notice signs of poor quality control in several places.Off the bat it was apparent that the quality of plastic used in this build is very cheap, and the plastic manages to feel flimsy while looking flat and ugly. The PU leather covering on the seat and back of the chair looks substantially better, however there are several mysterious stains/residue patches on my unit that resemble grease or another industrial lubricant that can’t get off. That, coupled with the mangled zipper on my seat back upholstery mean I had to attach the back to the seat while wrangling the zipper closed so the entire back wasn’t popping open. I also spotted a few places where it looked like the plastic parts had been sanded/ground down accidentally at odd angles, but most of those are under the chair and out of my sight.Sitting in the chair feels decently comfy at first, and the lumbar pillow is nice and firm, but the longer I sat in it (4+ hours) the more I realized how bizarrely proportioned it was. The back of the chair is quite tall, but the piston below the seat only raises a handful of inches, and what I found is that the maximum height of the seat was still too low for me to sit and type comfortably at the lowest position on my sit-stand desk. I’m 6′ and I have a longer torso proportional to most other guys, but I still found myself reaching up to my desk, which was incredibly awkward and uncomfortable for long sessions. This may have been remedied if the arm rests were positioned correctly, but due to the substantial depth of the seat my elbows could not even touch the arm rests unless I had the seat back at 90 degrees. That proved not to be a viable solution because the angle of the headrest and very firm neck pillow actually pushed me down and hunched over when seated at 90 degrees.I could go on about the uncomfortable/non-ergonomic arm rests or the foam inside the seat cusion already deforming after 5 days of very light usage, but the point is you get what you pay for. With this HBada gaming chair you’re not paying a lot (relative to gaming chairs) and you’re certainly not getting a lot of value in return. It doesn’t feel good sitting in this chair, and I can’t imagine it would feel any better after a year or more of breaking it in. I’ll be attempting to return my unit, provided I can find a new box to ship it in. If that doesn’t work out I’m honestly considering just tossing this thing and going back to my $40 IKEA chair. Cheers.

Very Good Quality
The chair is everything all the other reviews have said; its very good quality, was really easy to assemble and I have never sat up so straight. The real reason I am writing is to tell about the comfort of the seat. If you are thicc, larger, or enjoy manspreading while you sit, this may not be the chair for you. The seat is very rigid. The sides have a metal frame in them and dig into your thighs. I found only sitting perfectly straight while gaming was comfortable enough, but there is very little padding. Reclining and spreading out and relaxing in this chair is not so comfortable.

Para una persona alta es un poco baja la altura de la silla y el colchón del respaldo de arriba queda bajo

Me gusto que tiene tanto un posicion flexible como fija para la inclinación del asiento