TP-Link 24 Port Gigabit Ethernet Switch Desktop/ Rackmount Plug & Play Shielded Ports Sturdy Metal Fanless Quiet Traffic Optimization Unmanaged (TL-SG1024S)

Superb performance & build quality, nightmare to mount on walls
Its a switch! Does what it needs to do.Pros:* Runs cold to the touch even when under decent load with multiple devices so its probably very energy efficient.* Seems to be very high performance! No latency or bandwidth changes vs direct CAT6a connection on gigabit ethernet. Tested with up to 3 devices under load. Latency was statistically unchanged and bandwidth/QoS was what you’d expect on paper so overhead is super low and on board protocols are implemented extremely well! Grain of salt though… I haven’t formally benchmarked or even really used SOHO switches since the 10/100 days. Maybe all makes/models are similar nowadays, but 20 years ago using switches was only a tad better than a hub in terms collision prevention and simple QoS.* Physical build quality is top notch, with one caveat (see Cons)Cons:* Design of metal casing is probably perfect for mounting on the side of standard 1U or 2U racks, warehouse racks, or anything else with standardized screw hole placement and (ideally) the ability to come in from behind or at least see what you’re doing. I needed to mount this to a wall in my home office where I couldn’t just screw into a rack with standard mounts and slide the switch in place 5 seconds later.There may be a much better way, but the only solution I could come up with (in order to use the rubber feet as standoffs to allow airflow) was to take the housing apart and unscrew/remove the PCB to see what the correct distance between screws needed to be. In theory this would be the last step but unfortunately problem #2 (really the only roadblock in retrospect) was that when wall mounting, the shape of the mounting cutouts are such that you (or at least me?)don’t give you enough “turning radius” to get the switch mounted without the offset from the screw head and the wall surface being stupidly long.The only solution where the standoff distance was both far enough to get the screw heads in there while ALSO getting it to mount securely without flapping around loose was to clip the opening a bit with sheet metal snips. This was a tad challenging but doable, mostly because of the cramped areas for maneuver.My recommended wall mount steps (unless someone has a better way) are:1. Insert the screws in the mounting holes, and position in the narrower “top” area where they loosely stay in place when held in by hand. This will be the distance when mounted. 2. Gently press the switch and screws into the wall just enough to create 2 small dents so you know where to drill.3. Drill. I didn’t need a drywall screw due to wood paneling, but use drywall screws if bare drywall. If you think you don’t need to just do it anyway. Its cheap, easy, and a good best practice to prevent yanks from plugged in devices, etc.4. Screw the screws in 95% of the way. You may be able to just mount the switch ok. If not, you may need to do step 5…5. (Optional). If necessary AND you know what you’re doing, AND you don’t care about warranties, open up the mounting cavity with metal snips, but only after you have unscrewed the device housing and have carefully removed all the (guts). Put them aside in an anti static bag to keep them safe.Start by clipping tiny slivers from the two mounting cavities on the bottom device housing piece. Adjust the screw depth until you can easily mount the housing without it feeling loose. You may need to test/adjust a few times, since the screw head will be blocked by sheet metal. This is the core design flaw, otherwise you could just (at worst) unscrew the top housing cover, remove the “guts”, and just screw it in by hand, with the final step being to put everything back together (annoying but simple if you own magnetic screwdrivers).Again, only do this if no viable alternatives exist for you, as I’m sure it voids the warranty.Conclusion? Buy this excellent product, just be prepared for a “project” if this is going on a wall in a SOHO setting.

Value for Money:First and foremost, this Ethernet splitter offers the best value for your money. For a very reasonable price, you get a reliable device that allows you to turn a single Ethernet port into four additional slots. It’s hard to find a more economical solution that delivers this level of performance and convenience.Performance and Reliability:The splitter is incredibly easy to set up. Simply plug it into your existing Ethernet port, and you’re ready to go. It works seamlessly behind my smart TV and desktop, providing stable and reliable connections to multiple devices without any noticeable degradation in speed or signal quality. I haven’t experienced any connectivity issues or interruptions, which is crucial for uninterrupted streaming or gaming.Design and Functionality:The compact and sturdy design of this splitter means it doesn’t take up much space and fits well in tight areas. The build quality is solid, and it feels durable, which is important for something that will be used regularly. The splitter is designed to handle multiple devices efficiently, making it a versatile addition to any setup.Practical Use:This splitter is perfect for home use, especially if you have multiple devices that need a wired connection but limited Ethernet ports. Whether it’s for your smart TV, desktop computer, gaming console, or any other Ethernet-enabled device, this splitter provides an easy way to expand your network capabilities.Summary:Overall, the Ethernet Splitter offers exceptional value and performance. It’s an economical solution that reliably turns one Ethernet port into four, making it an excellent choice for expanding connectivity in any home or office setup. If you’re in need of a splitter that doesn’t compromise on quality or performance, this is definitely the one to go for. Highly recommended!

Recomendo o uso, pois faz VLAN e outras características de switch gerenciável!!!!

Buen producto